LX Forums Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 107 Results
  1. Knowledge Base Submissions
    Information is based on personal experience but is not all inclusive. Let me know if anything needs added or updated. For the most part, this is an easy swap. You need a good set of tools to make things easier but a 10mm, 13mm, 15mm & 18mm sockets will get 90% done. And an engine hoist. 3.5...
  2. Engine / Intake / Exhaust / Performance
    Thought maybe somebody might like these $400 billet valve covers. SPELAB Billet Aluminum Engine Valve Covers 05-19 Dodge Hemi 5.7L 6.1L (spelabautoparts.com)
  3. Alberta LX (ALX)
    Hey fellow Bertans. I'm finally doing my valve seals and springs and I've realized that I need that special spring compressor. Instead of spending $150 to $200 on one does anyone want to sell theirs or better yet rent it out to me? Located in Red Deer btw
  4. Magnum General Discussion (2005 - 2008)
    Hey guys looking for some direction here. My cousin purchased a 2007 dodge magnum with the 3.5L 123,xxx miles. shortly after purchase the rpms at idle will drop real low around 580-610 and the engine will shake the car. There is no Check engine light but the car does have codes. I believe the...
  5. Transmissions Gears & Diffs
    Looks like I'll be pulling the Ding's valve body out, getting 3-4 flare and trying to tune it out isn't working. Going to change Conductor plate when it's out. Any particular brand or are they all the same?
  6. Want to Buy
    Looking for exhaust Valve Actuators and if possible the plugs that go to them with a couple of inches of wire. Let me know what you got
  7. 300 General Discussion (1st Gen - 2005 to 2010)
    First of all I am enquiring here because I am a fellow member and you guys are tops in my books. I have exhausted my efforts in another forum. The car in question is a 2006 acura csx 2.0l. No codes, things I have done to rectify. Fuel pump, injectors, coils plugs, battery, starter, intake and...
  8. 300C, Magnum RT & Charger RT (5.7L V8)
    Hey all, I'm doing my valve seals for the first time on my 08 5.7 turbo charger. The vehicle has about 150 000kms on it. Despite being turbo charged, compression is really good in all cylinders, I've kept it under 5.5psi and kept the Rev limiter set conservatively. I've never done valve seals...
  9. The SRT-8 (6.1L and 6.4L V8)
    Hey guys so been having a cel p0307, cylinder 7 missfire. Change plugs didn't solve issue and pulled the valve cover today. All springs look fine except for the cylinder 7 (exhaust/bottom side) spring. I will add some photos but it almost looks like it either broke the top "washer/hat" or as if...
  10. Engine / Intake / Exhaust / Performance
    Years ago I found a nifty little device to replace the pesky 1/4" NPT HEX head plug used to properly remove all air from our cooling systems during servicing: https://www.lxforums.com/board/engine-intake-exhaust-performance/375295-cooling-system-purge-valve.html I'm curious how many folks...
  11. Parts for Sale
    As the title says, I am looking for a stock pre-eagle intake manifold. Engine dropped a valve seat so I don't want to use the old one.
  12. General LX Discussion (1st Gen - 2005 to 2010)
    I used to own a 04 Magnum rt years ago, ran well for from the 90k to 130k mile range I owned it. Rather reliable. I am sorta looking at a 06 Charger RT that is MINT (not a cop car) MINT, with 28k on it. This car is like new. I have read up here on the valve seal drop or whatever it is called...
  13. Parts for Sale
    Looking to see if anyone has a valve spring tool lying around that they are willing to sell or loan, here is the one I was looking to purchase: LATE MODEL GEN 3 HEMI 5.7L, 6.1L, 6.2L, 6.4L VALVE SPRING COMPRESSOR | eBay
  14. Magnum General Discussion (2005 - 2008)
    Hey all, So as i'm explaining all this i just kind of noticed a trend when trying to go through all the past posts on here that had this code at least and almost all of them never show a end result which i will make sure to do as i'm chasing this issue! Now i know what the service manual states...
  15. The SRT-8 (6.1L and 6.4L V8)
    So I am wondering what we have as a quality valve train on the 6.4. Where is its limit? Has anyone encountered an issue? Autoshift is 61-6200 shift points, but manual mode cut off is like 63-6400 stock on most 6.4 liter MDS. So if the rpm range on the stick is higher, is it the cam an lifter...
  16. Charger Discussion (1st Gen - 2006 to 2010)
    Hey fello Dodge owners I drive a 07 Charger srt8 i need some clarification on the nag1, I’ve been having some trans problems for a while now and recently (about a week ago) the torque converter lock up has stop working. Still driving the car now but babying her I plan on just doing a complete...
  17. General LX Discussion (1st Gen - 2005 to 2010)
    Hi all, Long time no post, but my 3.5 has been running well. I have recently noted a strange "tap" sound in which appears to be coming from the short runner valve. I don't believe this is a rocker arm issue as I replaced mine a few years ago with the "revised" AA rocker arm sets. (and the...
  18. General LX Discussion (3rd Gen - 2015+)
    I started smelling burning oil a couple days ago. The odor only was noticed when sitting at idle. The smell is becoming progressively worst (heavier). I finally had a chance to take the cover off and oil was sitting on/in the fuel injector well. On the drivers side. The car still runs...
  19. The SRT-8 (6.1L and 6.4L V8)
    Which is A2Speed...dealing with a salesman there by the name of Eric. Kind of pushy valve job, head stud recommendations but besides that been a pleasure to talk too. Based off people getting their working done there, What do you think? 2006 6.1 Hemi w 100k miles. Cam is Inertia Max cam...
1-19 of 107 Results
Top