LX Forums Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 33 Results
  1. 300C, Magnum RT & Charger RT (5.7L V8)
    I know there must be some differences between the 03-08 5.7 pistons and the 09+ (Eagle) pistons to handle the smaller cylinder head chamber volume in the Eagle motors but I can't find definitive information anywhere. The rods are the same from 03 - current so the pistons must be different. Does...
  2. Charger Discussion (3rd Gen - 2015 +)
    I’m looking to get back into a charger and I found a supercharged 392 but it doesn’t have forged pistons. How bad is this?
  3. Engine / Intake / Exhaust / Performance
    it lives again Engine out,, torn down, and at machine shop, (they only build race engs and Toms know him for 30 yrs). Only two pistons survived unscathed. Surprised the cylinders are in great shape. #7 boy O boy The others, pistons took a beating. Not sure how the skirt get broken...
  4. The SRT-8 (6.1L and 6.4L V8)
    done
  5. Want to Buy
    Hello, I'm looking for lo mileage 6 piston calipers with rotors for scat pack challenger. If u got aftermarket 6 pistons feel free
  6. Engine / Intake / Exhaust / Performance
    I can get a 5.7 stroker block real cheap. I have in my possession a used 6.1 block that I was going to make a 426. Would it be better to sell 6.1 block and buy the new 396 5.7? Both will have forced induction. Currently has Procharger on 5.7 block with forged pistons only.
  7. Engine / Intake / Exhaust / Performance
    Hi, i've got a good deal on some 6.4 BGE parts (low miles on them) and would like to put this in my 6.1 block (2006 300c srt8) And i need info if anyone has done this before? Do i have to swap pistons + 6.4 rods or just pistons on 6.1 rods? ( is there a difference in rod lenght?)...
  8. Engine / Intake / Exhaust / Performance
    I have a 2018 392 on an engine stand that I'm prepping to drop into my 2018 300C (currently 5.7). I picked up some new in the box Mahle pistons with the understanding that they were the "drop-in" ones. Apparently, they are a couple years old and have been superceded with another part number so...
  9. Charger Discussion (3rd Gen - 2015 +)
    This would apply to 6 piston cars with the 2 piece rotors. My Daytona ticked turning on either direction. I read about the problem on here so I was far from the only one. I got my Hellcat a few months later and it ticked too on any turning. It’s embarrasing for both being brand new cars...
  10. Parts for Sale
    Interested in hellcat front rotors (6 pistons) and red calipers. I want to throw them on my first gen srt8 model.
  11. Magnum General Discussion (2005 - 2008)
    Greetings.. since another post about a top end swap on the Mag, ive gone another route. Bought a complete 5.7, and am starting from the block up. It had tossed a rod from what looked like water compression. It damaged the windage tray and pick up tube and thats it. So ive torn it down and...
  12. Power Adders
    I have broken the upper ring lands on 4 pistons of the drivers side of my procharged 6.4, but the pistons are perfect on the passenger side. Anybody have this happen before? Engine = P1 blower with 7psi, stock pistons, stock shorties good exhaust. Reputible tuner....I think its strange that...
  13. Charger Discussion (3rd Gen - 2015 +)
    As many of you know Livernois Motorsports is known far and wide for our experience in all of the late model performance vehicles on todays market but alot of you do not know how in depth we go with the builds we do here and all of the precautions we make to ensure the best customer experience...
  14. 300C, Magnum RT & Charger RT (5.7L V8)
    Short version: port and polished heads, bored block .010 over for a supercharger install (to clean up cylinders) valve seat drops and smacks cylinder, blows up engine.. engine builder covers in warranty, bores over .20, then during break in driving, previously unfound shrapnel from previous...
  15. 300C, Magnum RT & Charger RT (5.7L V8)
    Can anyone tell me what the piston dome volume is for stock pistons for both the 03-08 and also the 09 and up pistons. Also how far are they in the hole factory? Thanks for your time
  16. 300C, Magnum RT & Charger RT (5.7L V8)
    Can anyone tell me if I should have piston to valve clearance with my stock pistons with a big Hughes engines hydraulic roller for my 2004 n/a stock bottom end 5.7 . I’m running the ‘09 and up eagle heads with the 2.05 intake valve diameter with a .075 Cometic MLS gasket . The cam specs will be...
  17. Parts for Sale
    Does anyone have a set of 5.7L forged pistons/ rods for sale?
  18. Parts for Sale
    I am in need of a good set of rods and pistons for my stock bore 6.4 engine. Want to get rid of the factory stuff as I prepare for supercharging. Please pm me if you have anything for sale. I would consider a stroker kit as well as long as it would fit a 6.4 block. Thank you!
  19. Engine / Intake / Exhaust / Performance
    Hypothetical situation here...... 06 RT with complete eagle top end and aftermarket camshaft. 97 pump or e85. Is there any advantage to swapping out the pistons? Maybe to help with the compression or take advantage of good fuel and the camshaft?
  20. Parts for Sale
    Hey guys, Im looking for a set of 5.7/6.1 forged rods and pistons. Could be aluminum as well. Not looking to spend a fortune. Thanks guys!
1-20 of 33 Results
Top