LX Forums Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 309 Results
  1. Charger Discussion (3rd Gen - 2015 +)
    Picked up my first Dodge Charger last week, 2021 SmokeShow Scat Pack Widebody, after owning 4 Challengers over the past 11 years. I want to add a front splitter, lip, spoiler, and would very much appreciate any and all recommendations and advice. Thanks! ~Ray
  2. Charger Discussion (3rd Gen - 2015 +)
    My P Zero's did last 20k but the Hankook's only lasted about 33k. I replaced them with some Yokohama's as that is what I am running on my 08 Corvette. I was really surprised me is when I remove the tires to clear the weights of an clean the backside of the rim. The tires were obviously running...
  3. 300 General Discussion (1st Gen - 2005 to 2010)
    For starters.. not my car! :panic: Friend had an unfortunate incident with his car - 2006 300C SRT8, 160K miles, front end is toast now. Front bumper, passenger fender, headlights, hood (maybe saveable, just very minor damage at leading edge), engine compartment wiring harnesses at passenger...
  4. Tires, Wheels and Suspension
    It took me a while to pull the trigger and order these. I could have made them in the machine shop at work. And I actually drew each piece up in Solidworks with all the dimensions because I'm a nerd Engineer like that after I got them. But because I have little or no extra time these days, I...
  5. 300 General Discussion (2nd Gen - 2011 to 2014)
    Gentlemen, I have ordered the following parts: 1. Eibach anti-roll front sway bar Part# 2895.31 (35mm) 2. Eibach (pro kit) Springs Part# 28101-140 (less drop than sport line) from Summit Racing for their reasonable international shipping rates ($350) Preparing for the install, I am reading...
  6. Want to Buy
    I'm looking for a 2005-2010 300c Brilliant Black front bumper cover with no cracks or tears. North Florida - South Georgia area.
  7. Magnum General Discussion (2005 - 2008)
    So the TPMS has never worked on my car since I bought it. It was missing the front bumper cover and both transponders when I bought it. The 2 rear sensors have always reported correctly, but the fronts just show no readings. After finding and installing the transponders one time I got momentary...
  8. Magnum General Discussion (2005 - 2008)
    Hello, I have a 05 magnum I purchased and working through a 6.4 swap. Would like to put the 2015 charger front end on but can't seem to find anyone producing steel conversion fenders. Is anyone still producing these, if so where? Thanks! Ryan
  9. General LX Discussion (3rd Gen - 2015+)
    I know this was probably touched dozen of times at least, but not sure how to find it using search, so I decided to ask. I am planning to buy R/T Charger with 'current' look. Not new, but preferably less than 3-4 years old. The problem is, I'm not really fond of front looks of current...
  10. Magnum General Discussion (2005 - 2008)
    I have to rebuild the front suspension on my 2005 Magnum R/T and I'm looking for some suggestion on parts, sellers, brands, etc. Should I buy all new parts or should I just do the bushings on everything? Hit me with the 411, guys! :mrgreen:
  11. Tires, Wheels and Suspension
    I'd like to lower the front of my car about 2 inches, maybe 1.75 the fender gap is just too huge. I also don't want it to ride like a rock as I have about a mile long dirt road to travel daily. Thoughts?
  12. Charger Discussion (2nd Gen - 2011 to 2014)
    Surprised I couldn't find a thread on this, but does the Gen3 Charger front end (Fenders, fascia, hood and related parts) fit on a Gen 2 Charger. The main bodies looks pretty similar so seems like it would work. Anybody done it? Direct fit? Some fab work? Major PITA? Input appreciated.
  13. Challenger Discussion (2008 to 2014)
    I just bought a 2008 Dodge challenger SRT8 and noticed 245 size tires on front and 255 size on rear.Looks like that was a $50 option on window sticker.Is this correct?Can I run the same size on front and rear?If so which size would worK?Also,can I burn low grade octane fuel in car?
  14. Magnum General Discussion (2005 - 2008)
    A few years ago, I replaced some cracking skidplate/covers on the bottom front of the car, the one that bolts onto the bottom of the front fascia and the adjacent one beneath the engine. Both were Dorman units and I was initially happy with the plastic parts, both were thicker than the original...
  15. Magnum General Discussion (2005 - 2008)
    Anyone no were I can find a new or used 05-07 srt front bumper for sale. Can't find one anywhere
  16. 300 General Discussion (2nd Gen - 2011 to 2014)
    To the experts on suspension: The topic: We all so familiar with the piles of parts replaced "too often" on front suspension. I wonder what it takes to modify the 300s suspension? 1. Better quality parts than stock. 2. Better handling, solid ride on cornering etc. 3. Wider rear tires? The...
  17. Automotive Electronics (Audio & Video)
    I've done aftermarket car stereo installs in some of my previous vehicles and were all pretty easy. But I'm having an issue with one I just installed into my Magnum SRT8. The stereo I have is the ATOTO S8 Premium Android head unit. (ATOTO S8 Android Car in-Dash Navigation Stereo System,S8...
  18. General LX Discussion (1st Gen - 2005 to 2010)
    A couple weeks ago I replaced all the bushings in the front with energy suspension poly bushings. Being cheap I reused all the arms that have 116K miles on them. Well I guess I stressed the ball joints because a few are loose and clunking now. So the question is. Do I press out all the...
  19. Magnum General Discussion (2005 - 2008)
    Just picked up an 06 MSRT8 that has never had a front mount and my state requires a front plate. Does anyone know the part number for the front license plate bracket? Is it the same part # as the lower models? Or what else are you using instead?
  20. General LX Discussion (3rd Gen - 2015+)
    As March is right around the corner, I'm starting to think about getting ready for HPDE's this summer. On my 2016 Charger Scat Pack, I used the pinch welds to jack up the front for wheel/pad changes. However, after a couple seasons, even with the use of a grooved hockey puck the welds began to...
1-20 of 309 Results
Top