LX Forums Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 88 Results
  1. General LX Discussion (1st Gen - 2005 to 2010)
    I’m looking to swap a VVT Eagle Engine into my 2006 Chrysler 300C. My engine is trash and the car has just been sitting for a while and it’s time to put a motor in. If I wanted to put an Eagle Motor in what additional parts would be needed to make the car start? If I don’t do the Eagle swap I...
  2. The Knowledge Base X
    I’m not trying to go through the issues of removing the MDS Internals and plan on just keeping it off with a tune (Diablo). What cams would fit and work with the MDS internals still intact. What gains would/should I be seeing aswell?
  3. General LX Discussion (1st Gen - 2005 to 2010)
    Would the 6.1/6.4 headers bolt up to the motor? I know they wont bolt on to the exhaust but if they mount to the engine i will buy a set and get the appropriate mid-pipe and exhaust setup to match.
  4. Newbie Check-In
    My dodge magnum steering wheel control is not working the compass on the dash has 2 dash lines please help !!!
  5. 300 General Discussion (1st Gen - 2005 to 2010)
    Hey guys, pretty new here but I have a 2006 300c 5.7 that I just installed a stage 1 comp HRT cam in. I'm working on the tune with Sean from Hemifever, but after the install, my shifts have gone soft and almost slippy. Sean said he hasn't/can't change the logic on the trans on mine being a 2006...
  6. Tuning and Performance Programming
    Hello, I wanted to try to break into the tuning world and learn how to tune so I can get my own thing going eventually. I’ve installed the basic tunes on my car (05 300C/5.7) so far that are within the Predator tuner itself. So now I want to start customizing parameters here and there and...
  7. 300C, Magnum RT & Charger RT (5.7L V8)
    I have a 2005 Magnum with a 5.7 with well over 210,000 miles. It is pretty much stock outside of the billet tech catch can and Mopar CAI. I have decided to change the head gaskets (and all that job entails). It's been a few years since I've been able to wrench (kids and graduate school over the...
  8. Challenger Discussion (2008 to 2014)
    Hi all. I recently purchased a 2009 Challenger that was engine swapped with a 2006 5.7. It is currently not running. I understand the 2009 should be a VVT engine, and the 2006 is not. I am assuming the reason it will not run is because of this. Is there a pcm flash I could do to get the non...
  9. Charger Discussion (1st Gen - 2006 to 2010)
    Alright guys, I’ve been trying to find the source of a grinding noise for a while with no luck. I’ve searched the forums and haven’t found anyone else with this exact issue. It’s a 2007 Charger R/T, 5.7L, AWD, NAG1, 170k miles on her. This is what I got, under a load such as hard...
  10. 300 General Discussion (1st Gen - 2005 to 2010)
    I'm at wits end and really need some help here. 2005 300C 5.7 89,000 miles Ran fine and then one day would crank but not start. Wouldn't even catch. Starts briefly on starting fluid and dies immediately. NO Codes. After a bunch of new parts it starts with Starting Fluid but runs like it was...
  11. 300 General Discussion (3rd Gen - 2015 + )
    Figured I'd kick this here, So my buddy is replacing his stock exhaust off his 15' Hellcat. He had surgery on his arm a few weeks ago, and had already ordered it before hand, and like the awesome friend I am, offered to help him install the new set due to his handicap. Im almost certain the...
  12. 300C, Magnum RT & Charger RT (5.7L V8)
    Alright hopefully you guys on here can help me out here. Id like to prelude what im about to say by stating that ive looked and read literally hundreds of threads on different forums and still no dice. So i got a 08 300c 5.7l awd from a guy for 900 bucks. Has SLP loudmouth 1 exhaust and a diablo...
  13. 300C, Magnum RT & Charger RT (5.7L V8)
    The bolts come loose, and I mean completely loose from the Block, but I can't remove the bolt from the Intake Manifold. It's as if there is some sort of "retainer" on the underside of the Intake Manifold keeping it attached so I can't lift them out. What gives???
  14. Want to Buy
    Hey guys, I recently bought a 2006 Jeep Grand Cherokee and she needs a new motor. Low oil pressure, smoke... She's EOL. looking to find a long block so I can do a weekend swap. The lower the miles the better. Let me know what you have and what you are hoping to get for it. I have some nice...
  15. General LX Discussion (1st Gen - 2005 to 2010)
    What all would be necessary when swapping a 6.1L Camshaft into a 5.7L Hemi Block. Right now I'm thinking I would need 6.1 lifters, pushrods, and an MDS delete kit. Is there anything else to think about when doing this swap?
  16. 300C, Magnum RT & Charger RT (5.7L V8)
    My buddy asked me a question that I'm not technically inclined to answer. He has a 2012 Ram pickup with a 5.7 Hemi. Has new coil, new injector, new spark plugs. Performed compression test run and it has a 150 psi. It does not skip on idle or at Cruise speed only under acceleration. Any help...
  17. 300C, Magnum RT & Charger RT (5.7L V8)
    Hello all. 2010 Chrysler 300S Long tube headers, full 3" exhaust with high flow cats Comp 274 Phaser Cam Tuned with an exhaust leak stock converter After we got the exhaust leak fixed, it seems I can't always come to a stop with it in drive, or else it surges and gives itself throttle to not...
  18. Want to Buy
    Hey guys know anyone that has a motor for a 2008 Chrysler 300C?
  19. 300C, Magnum RT & Charger RT (5.7L V8)
    Can anyone tell me if I should have piston to valve clearance with my stock pistons with a big Hughes engines hydraulic roller for my 2004 n/a stock bottom end 5.7 . I’m running the ‘09 and up eagle heads with the 2.05 intake valve diameter with a .075 Cometic MLS gasket . The cam specs will be...
  20. 300C, Magnum RT & Charger RT (5.7L V8)
    I’m currently rebuilding my 5.7 Hemi bottom end with stock crank, rods, and pistons, although it has clevite P bearings and the rings will be gapped for a small shot of nitrous. The top end will be ‘13 eagle heads with a big custom ground Hughes engines camshaft, and a Ritter racing drag pack...
1-20 of 88 Results
Top